ABH-300-AQ
Air-quality monitor
Cleanrooms & incubators
CO₂, particulate matter and VOC channels alongside T/RH and pressure — cleanrooms, CO₂ incubators and controlled environments.
Design visualization · 106.4 × 150.0 × 29.3 mm
ABH-300-AQ — every number a QA team asks for
Channel-level accuracy, memory depth in readings, enclosure geometry and the firmware trust chain — the full picture before you ask for the pilot.
| Product type | Industrial · Wi-Fi monitor |
| Sensing channels | 11 (CO₂ · Particulate + VOC · Ambient T + RH + pressure) |
| CO₂ | SCD40/41 (Exp-B) · 400–5000 ppm |
| Particulate + VOC | SEN55 (Exp-B) · PM1/2.5/4/10 + VOC index |
| Ambient T + RH + pressure | SHT41 + BMP390 on-board |
| Measurement accuracy | Sensor ±0.2 °C typ · ±0.4 °C max (0–65 °C) on-board SHT41 · system class 1 as-shipped on live USB (class 0.5 on battery / with USB power save) |
| Display & indication | 1.54″ e-paper 200 × 200 · −25…+50 °C · holds last reading while asleep |
| Connectivity | Wi-Fi 2.4 GHz (ESP32-C3-MINI-1U) · MQTT over TLS 1.2+ — Internal FPC · ≤2 dBi |
| Power | USB 5 V + Molicel P28A 18650 pack |
| Battery life | ≈56 d USB-loss backup (calculated, spec-compliant logging at firmware defaults; ≈35 d at −20 °C) — ≈56 d USB-loss backup (calculated) |
| Memory | 16 MB W25Q128JV · 409,600 readings · separate never-erased audit region |
| Sample interval | 1 s minimum · sensor-dependent |
| Enclosure | 106.4 × 150.0 × 29.3 mm · PC/ABS · UL94 V-0 · UV-stabilised · RAL 7035 grey · vented |
| Ingress protection | IP54 (design target, vented for air quality) |
| Mounting | Keyhole (2×) + bonded magnets · M12 cable ports |
| Operating band | −25 to +50 °C (e-paper limit) |
| Firmware | Signed .abhfw packages · dual-bank A/B · RSA-2048 · trial boot with automatic rollback · MQTT over TLS 1.2+ with per-device credentials · X.509 client certificates / mTLS on the roadmap |
| Factory identity | ABH-[model]-[YYWW]-[5-digit sequence] — factory identity written to the ID EEPROM |
| Ports | USB-C · vented sensor bay |
The ABH line is at the design-frozen, pre-production stage: every enclosure has passed generated fit-check geometry (791/791 checks, 20/20 SKUs) and every battery-life, drop, thermal and IP figure shown is a calculated or simulated design estimate — measured values replace them as validation hardware runs. Regulatory marks above are the certification roadmap, not held certificates.
- Vented housing with ePTFE membranes — the sensors breathe, the electronics don't
- One record for the whole room: CO₂, PM, VOC, T, RH and pressure together
- Alert rules on any channel, same Flink CEP engine as temperature
- Cleanrooms & CO₂ incubatorsCO₂, particulate and VOC channels alongside T/RH and pressure in a vented IP54 build.
- ABH-300-AQ datasheetPDFFull specification, applications and probe options
- ABH range overviewAll 20 SKUs and the platform story
- Platform capability briefSoftware, compliance and architecture
Datasheets describe the current design release (ABH-PLATFORM 0.0.4). Battery-life and IP figures inside are calculated design estimates; measured values follow validation hardware.
One PCB, one firmware, one compliant record
One 80 × 50 mm 4-layer platform PCB — 146 parts, single-sided SMT — becomes 20 SKUs by BOM selection and a SKU record in the on-board ID EEPROM.
Signed .abhfw packages · dual-bank A/B · RSA-2048 · trial boot with automatic rollback
MQTT over TLS 1.2+ with per-device credentials · X.509 client certificates / mTLS on the roadmap
Plug an offline logger into a PC and it enumerates a FAT16 drive with README.TXT, DATA.CSV and an ECDSA P-256-signed REPORT.PDF — a self-verifying trip record.
Probe channel templates live in the ID EEPROM; the platform tracks NIST-traceable calibration certificates, due dates and reminders per probe.
Certification roadmap: EN 12830:2018 — temperature recorders · CE — RED / EMC / safety · FCC Part 15 · WHO PQS E006 — vaccine cold chain · IEC 61010-1 / IEC 62368-1 · UN 38.3 / IEC 62133-2 — cells & packs — targets, not held certificates.
Put the ABH-300-AQ to work
Book a demo and we'll scope a pilot around your sites — quantities, probes, alert rules and the reports your QA team will hand the inspector.